Please use this identifier to cite or link to this item:
https://hdl.handle.net/10321/1750
DC Field | Value | Language |
---|---|---|
dc.contributor.advisor | D'Almaine, George Frederick | - |
dc.contributor.author | Reddy, Dwayne Jensen | en_US |
dc.date.accessioned | 2016-11-18T08:01:24Z | - |
dc.date.available | 2016-11-18T08:01:24Z | - |
dc.date.issued | 2016 | - |
dc.identifier.other | 663054 | - |
dc.identifier.uri | http://hdl.handle.net/10321/1750 | - |
dc.description | Submitted in the fulfilment of the requirements for the Master of Engineering, Durban University of Technology, Durban, South Africa, 2016. | en_US |
dc.description.abstract | The effectiveness of using a low cost non - platinum (Pt) material for the catalyst layer of a polymer electrolyte fuel cell (PEMFC) was investigated. A test cell and station was developed. Two commercial Pt loaded membrane electrode assemblies (MEA) and one custom MEA were purchased from the Fuelcelletc store. Hydrogen and oxygen were applied to either side of the custom MEA which resulted in an additional sample tested. An aluminium flow field plate with a hole type design was manufactured for the reactants to reach the reaction sites. End plates made from perspex where used to enclose the MEA, flow field plates, and also to provide reactant inlet and outlet connection points. The developed test station consisted of hydrogen and oxygen sources, pressure regulators, mass flow controllers, heating plate, and humidification units. A number of experimental tests were carried out to determine the performance of the test cells. These tests monitored the performance of the test cell under no-load and loaded conditions. The tests were done at 25 °C and 35 °C at a pressure of 0.5 bar and varying hydrogen and oxygen volume flow rates. The no-load test showed that the MEA’s performed best at high reactant flow rates of 95 ml/min for hydrogen and 38 ml/min for oxygen. MEA 1, 2, 3, and 4 achieved an open circuit voltage (OVC) of 0.936, 0.855, 0.486 and 0.34 V respectively. The maximum current density achieved for the MEAs were 0.3816, 0.284, 15x10-6, and 50x10-6 A/cm2. Under loaded conditions the maximum power densities achieved at 25 °C for MEA’s 1, 2, 3, and 4 were 0.05, 0.038, 2.3x10-6, 1.99x10-6 W/cm2 respectively. Increasing the temperature by 10°C for MEA 1, 2, 3, 4 resulted in a 16.6, 22.1, 1.79, 10.47 % increase in the maximum power density. It was found that increasing platinum loading, flow rates, and temperature improved the fuel cell performance. It was also found that the catalytic, stability and adsorption characteristics of silver did not improve when combining it with iridium (Ir) and ruthenium oxide (RuOx) which resulted in low current generation. The low maximum power density thus achieved at a reduced cost is not feasible. Thus further investigation into improving the catalytic requirements of non Pt based catalyst material combinations is required to achieve results comparable to that of a Pt based PEMFC. | en_US |
dc.format.extent | 92 p | en_US |
dc.language.iso | en | en_US |
dc.subject.lcsh | Fuel cells | en_US |
dc.subject.lcsh | Catalysts | en_US |
dc.subject.lcsh | Electrodes | en_US |
dc.subject.lcsh | Polyelectrolytes | en_US |
dc.subject.lcsh | Proton exchange membrane fuel cells | en_US |
dc.title | The effectivness of using a non-platinum material combination for the catalyst layer of a proton exchange membrane fuel cell | en_US |
dc.type | Thesis | en_US |
dc.description.level | M | en_US |
dc.identifier.doi | https://doi.org/10.51415/10321/1750 | - |
local.sdg | SDG07 | - |
item.languageiso639-1 | en | - |
item.fulltext | With Fulltext | - |
item.openairecristype | http://purl.org/coar/resource_type/c_18cf | - |
item.grantfulltext | open | - |
item.openairetype | Thesis | - |
item.cerifentitytype | Publications | - |
Appears in Collections: | Theses and dissertations (Engineering and Built Environment) |
Files in This Item:
File | Description | Size | Format | |
---|---|---|---|---|
REDDYDJ_2016.pdf | 2.18 MB | Adobe PDF | View/Open |
Page view(s)
671
checked on Dec 22, 2024
Download(s)
335
checked on Dec 22, 2024
Google ScholarTM
Check
Altmetric
Altmetric
Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.